Qualitative analysis test

To detect one cation and one anion from the

following:


(Insoluble salts to be excluded)

Apparatus:

Micro test-tubes with stand, test tube holder, kerosene burner,

W-tube, well plate, dispensing bottles, china dish, cotton swabs,

charcoal cavity, W. Tube etc.

Chemicals:

6MH2

SO4, 6MHCl, lime water, sodium carbonate, sodium metal, BaCl2

solution, KMnO4

solution, KI solution, starch solution, acetic acid

Introduction:

The inorganic qualitative analysis involves the identification of ions

present in a sample. The salt consists of anion and cation. The basis

of identification is the observed chemical behaviour of the

components. The salt analysis may be systematically carried out in

the following three steps:

i) Preliminary examination

ii) Detection of anions and

iii) Detection of cations

Preliminary examination:

First we proceed to examine the physical properties of the salt. This

is followed by the action of heat on the salts and also certain tests,

such as flame test etc.

Detection of Anions:

A preliminary hint about some anions may be obtained by the formation

of volatile or gaseous products when the salt is treated with



i) dil.H2SO4 (for CO3 2-, S2-, SO3 2-, N02 - and CH3COO-) ii) conc.H2SO4 (for C1- , Br-, I- and NO3 - ) 1. Take about 10 mg of the salt in a dry test tube with the help of a spatula. 2. Heat the test tube over the burner and observe the change. Note the colour and odour of the gases if evolved as given in Table 2. Table 2 : Action of Heat Observation Inference Chemistry Involved Ammonia gas evolves NH4 + (NH4) 2 CO3 →NH3+CO2+H2O Carbon dioxide evolves CO3 2– present CaCO3 → CaO + CO2 Sulphur dioxide evolves SO4 2- may be 2FeSO4 → Fe2O3+ SO2 + SO3 present Nitrogen dioxide evolves NO3 – 2Cu(NO3)2 →2CuO + 4NO2 +O2 Colour of the salt on heating changes from 1. Some salts change their Cu2+ salt By losing water of colour blue to white crystallization 2. Green to yellow Ni2+ salt 3. White (when cold) to Zn2+ salt yellow (when hot) Flame Test Prepare a paste of small amount of the salt with one or two drops of conc.HCl on a watch glass. Take the paste on the loop of Nichrome wire or cotton swab, put it in the burner’s flame and observe the colour.

Comments

Post a Comment

Popular posts from this blog

Young’s Modulus ‘Y’ By Searle’s Method

Image
Aim:  To determine Young’s modulus of elasticity of the material of a given wire by Searle’s method.  Procedure: i. Arrange the experimental set up as shown in diagram. Attach a zero load (slotted hanger it self) and dead load (E) to the frames of the experimental wire and dummy wire respectively so that the wires become free of kinks and remain vertically straight. ii. With the help of micrometer screw gauge, find the correct diameter of the wire at three different places. At every place two readings of the micrometer are taken while holding it in one position and another perpendicular to it by rotating through 90°. iii. In all, six readings of the diameter of the wire are taken. Hence mean diameter and radius of the wire is found out. iv. Adjust the spirit level so that the air bubble is at the centre. Note down the reading of the micrometer screw (M) attached to it. This is zero reading. (This contains main scale reading ...
Read more

Spectrometer I - Refractive index of the prism.

PROCEDURE: I. To determine the angle of the prism 1. The preliminary adjustments for telescope, prism and the collimator are done. 2. The slit is illuminated by a sodium vapour lamp. The prism table is mounted vertically. 3. The refracting edge of the prism placed facing the collimator. 4. The image on one side is seen through through the telescope and the vernier readings (R1) are noted. 5. The image on other side is seen through through the telescope and the vernier readings (R2) are noted. 6. 2A = R1  R2  hence the angle of the prism ‘A’ is determined using A =  II. To determine the angle of minimum deviation 1. The edge of the prism is placed facing away from the collimator. 2. The refracting image is obtained in the telescope. The prism table is slowly rotated. 3. The image moves, then stops and turns back. The position of the image where the image stops and turns back is the minimum deviation. 4. The vernier readings (R3) are noted at this position and the direct ray reading (...
Read more

laboratory work

Introduction  The crucial role of practical work and experimentation in science curriculum is universally accepted. This is more so in chemistry which is an experimental science. Most of the concepts in this area are better understood by doing the practical work. The aims and objectives of practical work in the laboratory can be stated as follows:  1. better understanding of scientific concepts and principles.  2. promotion of basic skills and competencies (procedural and manipulative skills, observational skills, drawing skills, reporting and interpretation skills).  3. awakening and maintaining curiosity in the learning environment.  The laboratory work is an indispensable part of chemistry instruction. Despite several laudable efforts in the past, experiments, by and large, have continued to be marginalised in school education, and have not received the due importance. There are several factors which contribute towards neglect of the labora...
Read more